收藏本站
14
5.3
Communication
When communication of either text or commands is interrupted, try the steps below.
?
First, check the communication cable for continuity. If you don't have an ohm meter, try using a
different communication cable. If you are using a PC try using a different Com/USB Port.
?
Next, please ensure that the display module is set to communicate on the protocol that you are
using, by checking the Protocol Select Jumpers.
?
In serial and USB protocols, ensure that the host system and display module are both
communicating on the same baud rate. The default rate for the display module is 19200 bps.
?
Match Rx from your display to the transmitting pin from your host and the
Tx pin to the
receiving pin.
?
If you are communicating to the display via I2C*
please ensure that the data is being sent to the
correct address. The default slave address for the display module is 80.
?
In I2C mode, connect Rx to the clock line of your controller and Tx to the data output.
?
Unlock the display. See the Set and Save Data Lock command for more info.
?
Finally, you may reset the display to its default settings using the Manual Override
procedure
outlined below.
*Note:
I2C communication will always require pull up resistors on SCL and SDA of one to ten kilohms.
5.4
Manual Override
Should the settings of your display become altered in a way that dramatically impacts usability, the
default settings can be temporarily restored. To override the display, please follow the steps below.
1.
Disconnect power from your display.
2.
Place a jumper on the middle two keypad pins, R5 and C1.
3.
Reconnect power to your unit, and wait for the start screen before removing the jumper.
4.
Settings will be temporarily**
overridden to the defaults listed in the Manual Override Settings
table. At this point any important settings, such as contrast, backlight, or baud rate, should not only
be set but saved so they remain when the override is removed.
Parameter
Value
Backlight
255
Contrast
128
Baud Rate
19200
I2C Address
80
Table 11: Manual Override Settings
**Note:
The display module will revert back to the old settings once turned off,
unless desired settings are saved.
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
VK204-25-422 VF CHARACTER DISPLAY 20X4 RS422
VK204-25-VPT VFD ALPHA/NUM DISPLAY 20X4
VLM-532-42-SCA LASER MODULE 532NM 1-5MW DOT
VLM-532-46-LCA LASER MODULE 532NM 1-5MW LINE
VLM-635-14-SPA LASER MODULE 635NM 1-5MW DOT
VLM-635-15-LPA LASER MODULE 635NM 1-5MW DOT
VLM-650-00 LASER MODULE 650NM 1-5MW DOT
VLM-650-07-LPT LASER MODULE 650NM 1-5MW DOT
相关代理商/技术参数
VK204-24-USB 功能描述:真空荧光显示器 - VFD 20x4-24 Ch. USB VFD RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25 功能描述:真空荧光显示器 - VFD Vacuum Florescent Blue/Green Text RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422 功能描述:真空荧光显示器 - VFD 20x4 Grn Txt Blk B/G No Backlight 25 key RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-E 功能描述:真空荧光显示器 - VFD 20x4Grn Txt Blk B/G No B/L Ext. Temp RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-V 功能描述:真空荧光显示器 - VFD 20x4 Grn Txt Blk B/G No B/L Ext. Volt RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-VPT 功能描述:真空荧光显示器 - VFD 20x4 Grn Txt Blk B/G No B/L Volt Reg RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装:
VK204-25-422-VPT-E 制造商:Matrix Orbital 功能描述:20x4 VFD,RS422,25key Wide Volt, Ext Temp
VK204-25-E 功能描述:真空荧光显示器 - VFD 20X4 DISPLAY RoHS:否 制造商:Noritake 产品:Graphic Display Modules 字符计数 x 行: 模块大小 - 宽x高x厚:230 mm x 78 mm x 15 mm 观察区域 - 宽x高:166.25 mm x 41.45 mm 接口: 电压额定值:5 V 工作温度范围:- 40 C to + 85 C 封装: